Fujitsu SPARC T5440 Bedienungsanleitung PDF herunterladen (Seite 159)

Servicing Field-Replaceable Units 133

FIGURE: Removing the Hard Drive Backplane

4. Lift the backplane up and out of the system.

▼ Install the Hard Drive Backplane

1. Lower the hard drive backplane into the system.

Align the tab on the lower edge the backplane with the corresponding slot in the

chassis floor.

1 2 ... 154 155 156 157 158 159 160 161 162 163 164 ... 213 214

SPARC Enterprise 3
T5440 Server 3
Service Manual 3
Contents 7
Field-Replaceable Units 176 14
Index 179 14
For Safe Operation 15
Before You Read This Document 15
Related Documentation 17
Title Description Manual Code 18
UNIX Commands 19
Text Conventions 19
Prompt Notations 20
Notes on Safety 21
Task Warning 22
Product Handling 23
Alert Label 24
Preface xxiii 25
Identifying Server Components 27
Front Panel Diagram 29
Front Panel LEDs 30
Rear Panel Diagram 31
Rear Panel LEDs 33
Ethernet Port LEDs 34
Managing Faults 35
Diagnostic Flowchart 37
Diagnostic Flowchart Actions 38
Managing Faults 13 39
ILOM Overview 41
ILOM Fault Management 42
SunVTS Overview 44
Managing Faults 19 45
Managing Faults 21 47
Managing Faults 23 49
Managing Faults 25 51
Controlling How POST Runs 52
▼ Change POST Parameters 53
▼ Run POST in Maximum Mode 54
Managing Faults 29 55
Detecting Faults 56
Command” on page 33 57
Commands 61
▼ Check the Message Buffer 62
▼ View ILOM Event Log 63
Managing Faults 39 65
SunVTS Software Packages 67
Detecting Faults Using POST 68
Clearing Faults 73
Managing Faults 49 75
Disabling Faulty Components 76
▼ Disable System Components 78
▼ Re-Enable System Components 78
ILOM-to-ALOM CMT Command 79
Reference 79
Managing Faults 55 81
Safety Information 85
Safety Symbols 86
Antistatic Wrist Strap 87
Antistatic Mat 87
Required Tools 88
Remotely 88
Powering Off the System 89
Position 91
1 Slide Rail Lock 92
2 Inner Rail Release Button 92
Figure Legend 94
Removing the Top Cover 95
Servicing Hard Drives 98
Removing a Hard Drive 100
# cfgadm -al 100
Installing a Hard Drive 102
# cfgadm -c configure c0::sd1 102
▼ Remove a Hard Drive 103
▼ Install a Hard Drive 104
Hard Drive Device Identifiers 105
Hard Drive LEDs 106
Servicing Fan Trays 107
Next Steps 108
▼ Remove a Fan Tray 109
▼ Install a Fan Tray 110
Fan Tray Device Identifiers 110
Fan Tray Fault LED 110
Servicing Power Supplies 111
Removing a Power Supply 113
Installing a Power Supply 114
▼ Remove a Power Supply 115
▼ Install a Power Supply 116
Power Supply LED 117
Servicing PCIe Cards 118
▼ Remove a PCIe Card 119
▼ Install a PCIe Card 120
▼ Add a PCIe Card 120
PCIe Device Identifiers 122
Related Information 123
Servicing CMP/Memory Modules 124
▼ Remove a CMP/Memory Module 125
▼ Install a CMP/Memory Module 126
▼ Add a CMP/Memory Module 127
Servicing FB-DIMMs 130
▼ Remove FB-DIMMs 131
▼ Install FB-DIMMs 131
▼ Verify FB-DIMM Replacement 132
▼ Add FB-DIMMs 135
FB-DIMM Device Identifiers 138
Servicing the Front Bezel 141
▼ Remove the Front Bezel 142
▼ Install the Front Bezel 143
Servicing the DVD-ROM Drive 144
▼ Install the DVD-ROM Drive 145
Servicing the IDPROM 149
▼ Install the IDPROM 150
Servicing the Battery 151
Servicing the Motherboard 161
▼ Install the Motherboard 163
Installing the Motherboard 164
Servicing the Front I/O Board 172
▼ Remove the Front I/O Board 173
▼ Install the Front I/O Board 174
▼ Install the Top Cover 176
1 Inner rail release button 178
2 Slide rail lock 178
▼ Power On the Server 179
I/O Connections to CMP/Memory 182
● Do one of the following: 187
System Bus Topology 188
Connector Pinouts 193
1 Request to Send 5 Ground 194
4 Ground 8 Clear to Send 194
Serial Port Connector Pinouts 195
USB Connector Pinouts 196
Connector Pinouts 171 197
Server Components 199
Customer-Replaceable Units 200
Field-Replaceable Units 202
Numerics 205
Index 181 207
Index 183 209
Index 185 211

Kommentare zu diesen Handbüchern

Keine Kommentare

Fujitsu SPARC T5440 Bedienungsanleitung Seite 159

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Computers Fujitsu SPARC T5440