Fujitsu SPARC T5440 Bedienungsanleitung Seite 110
- Seite / 214
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
84 SPARC Enterprise T5440 Server Service Manual • July 2009
▼ Install a Fan Tray
1. Slide each fan tray into its bay until it locks into place.
Ensure that the fan tray is oriented correctly. Airflow in the system is from front to
back.
2. Verify proper fan tray operation.
See “Fan Tray Fault LED” on page 84.
Next Steps
If you are replacing the fan trays after performing another service procedure,
complete these steps.
■ “Slide the Server Into the Rack” on page 151
■ “Power On the Server” on page 153
Fan Tray Device Identifiers
TABLE: Fan Tray Device Identifiers on page 84 describes the FRU device names for
the fan trays in the server.
Related Information
■ “Managing Faults” on page 9
■ “Hot-Pluggable and Hot-Swappable Devices” on page 72
■ “Fan Tray Fault LED” on page 84
Fan Tray Fault LED
Each fan tray contains a Fault LED that is located on the top panel of the server. The
LED is visible when you slide the server partially out of the rack.
TABLE: Fan Tray Device Identifiers
Device Device Identifier
FT0 /SYS/MB/FT0
FT1 /SYS/MB/FT1
FT2 /SYS/MB/FT2
FT3 /SYS/MB/FT3
- SPARC Enterprise 3
- T5440 Server 3
- Service Manual 3
- Contents 7
- Field-Replaceable Units 176 14
- Index 179 14
- For Safe Operation 15
- Before You Read This Document 15
- Related Documentation 17
- Title Description Manual Code 18
- UNIX Commands 19
- Text Conventions 19
- Prompt Notations 20
- Notes on Safety 21
- Task Warning 22
- Product Handling 23
- Alert Label 24
- Preface xxiii 25
- Identifying Server Components 27
- Front Panel Diagram 29
- Front Panel LEDs 30
- Rear Panel Diagram 31
- Rear Panel LEDs 33
- Ethernet Port LEDs 34
- Managing Faults 35
- Diagnostic Flowchart 37
- Diagnostic Flowchart Actions 38
- Managing Faults 13 39
- ILOM Overview 41
- ILOM Fault Management 42
- SunVTS Overview 44
- Managing Faults 19 45
- Managing Faults 21 47
- Managing Faults 23 49
- Managing Faults 25 51
- Controlling How POST Runs 52
- ▼ Change POST Parameters 53
- ▼ Run POST in Maximum Mode 54
- Managing Faults 29 55
- Detecting Faults 56
- Command” on page 33 57
- Commands 61
- ▼ Check the Message Buffer 62
- ▼ View ILOM Event Log 63
- Managing Faults 39 65
- SunVTS Software Packages 67
- Detecting Faults Using POST 68
- Clearing Faults 73
- Managing Faults 49 75
- Disabling Faulty Components 76
- ▼ Disable System Components 78
- ▼ Re-Enable System Components 78
- ILOM-to-ALOM CMT Command 79
- Reference 79
- Managing Faults 55 81
- Safety Information 85
- Safety Symbols 86
- Antistatic Wrist Strap 87
- Antistatic Mat 87
- Required Tools 88
- Remotely 88
- Powering Off the System 89
- Position 91
- 1 Slide Rail Lock 92
- 2 Inner Rail Release Button 92
- Figure Legend 94
- Removing the Top Cover 95
- Servicing Hard Drives 98
- Removing a Hard Drive 100
- # cfgadm -al 100
- Installing a Hard Drive 102
- # cfgadm -c configure c0::sd1 102
- ▼ Remove a Hard Drive 103
- ▼ Install a Hard Drive 104
- Hard Drive Device Identifiers 105
- Hard Drive LEDs 106
- Servicing Fan Trays 107
- Next Steps 108
- ▼ Remove a Fan Tray 109
- ▼ Install a Fan Tray 110
- Fan Tray Device Identifiers 110
- Fan Tray Fault LED 110
- Servicing Power Supplies 111
- Removing a Power Supply 113
- Installing a Power Supply 114
- ▼ Remove a Power Supply 115
- ▼ Install a Power Supply 116
- Power Supply LED 117
- Servicing PCIe Cards 118
- ▼ Remove a PCIe Card 119
- ▼ Install a PCIe Card 120
- ▼ Add a PCIe Card 120
- PCIe Device Identifiers 122
- Related Information 123
- Servicing CMP/Memory Modules 124
- ▼ Remove a CMP/Memory Module 125
- ▼ Install a CMP/Memory Module 126
- ▼ Add a CMP/Memory Module 127
- Servicing FB-DIMMs 130
- ▼ Remove FB-DIMMs 131
- ▼ Install FB-DIMMs 131
- ▼ Verify FB-DIMM Replacement 132
- ▼ Add FB-DIMMs 135
- FB-DIMM Device Identifiers 138
- Servicing the Front Bezel 141
- ▼ Remove the Front Bezel 142
- ▼ Install the Front Bezel 143
- Servicing the DVD-ROM Drive 144
- ▼ Install the DVD-ROM Drive 145
- Servicing the IDPROM 149
- ▼ Install the IDPROM 150
- Servicing the Battery 151
- Servicing the Motherboard 161
- ▼ Install the Motherboard 163
- Installing the Motherboard 164
- Servicing the Front I/O Board 172
- ▼ Remove the Front I/O Board 173
- ▼ Install the Front I/O Board 174
- ▼ Install the Top Cover 176
- 1 Inner rail release button 178
- 2 Slide rail lock 178
- ▼ Power On the Server 179
- I/O Connections to CMP/Memory 182
- ● Do one of the following: 187
- System Bus Topology 188
- Connector Pinouts 193
- 1 Request to Send 5 Ground 194
- 4 Ground 8 Clear to Send 194
- Serial Port Connector Pinouts 195
- USB Connector Pinouts 196
- Connector Pinouts 171 197
- Server Components 199
- Customer-Replaceable Units 200
- Field-Replaceable Units 202
- Numerics 205
- Index 181 207
- Index 183 209
- Index 185 211
Verwandte Produkte und Handbücher für Computers Fujitsu SPARC T5440
Computers Fujitsu Service View Resource Orchestrator Cloud Edition V Bedienungsanleitung
(102 Seiten)
(102 Seiten)
Computers Fujitsu 2000 Bedienungsanleitung
(66 Seiten)
(66 Seiten)
Computers Fujitsu M3000 Bedienungsanleitung
(76 Seiten)
(76 Seiten)
Computers Fujitsu ServerView Respurce Orchestrator Virtual Edition V Bedienungsanleitung
(247 Seiten)
(247 Seiten)
Computers Fujitsu BX900 S1 Bedienungsanleitung
(142 Seiten)
(142 Seiten)
Computers Fujitsu M5000 Bedienungsanleitung
(310 Seiten)
(310 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern