Fujitsu SPARC T5440 Bedienungsanleitung PDF herunterladen (Seite 119)

Servicing Customer-Replaceable Units 97

3. Remove the PCIe card the system.

4. Place the PCIe card on an antistatic mat.

5. If you are not replacing the PCIe card, install a PCIe filler panel in its place.

6. Close the PCIe card latch.

▼ Install a PCIe Card

1. Identify the correct slot for installation.

2. Open the PCIe card latch.

1 2 ... 114 115 116 117 118 119 120 121 122 123 124 ... 211 212

SPARC Enterprise T5440 Server 1
Service Manual 1
Contents 5
For Safe Operation 13
Before You Read This Document 13
Related Documentation 14
Preface xv 15
UNIX Commands 16
Text Conventions 17
Prompt Notations 17
Alert Messages in the Text 18
Notes on Safety 19
Product Handling 20
Alert Label 21
Documentation Feedback 22
Identifying Server Components 23
Front Panel Diagram 25
Front Panel LEDs 27
Rear Panel Diagram 28
Rear Panel LEDs 30
Ethernet Port LEDs 31
Managing Faults 33
Server Diagnostics Overview 34
Diagnostic Flowchart 35
Diagnostic Flowchart Actions 37
ILOM Overview 40
ILOM Fault Management 41
Oracle VTS Overview 43
Managing Faults 27 49
(ILOM show Command) 50
Controlling How POST Runs 51
POST Parameters 52
▼ Change POST Parameters 53
▼ Run POST in Maximum Mode 54
Managing Faults 33 55
Detecting Faults 56
Managing Faults 35 57
Managing Faults 37 59
Commands) 61
▼ Check the Message Buffer 61
▼ View ILOM Event Log 63
About Oracle VTS Software 64
Managing Faults 43 65
Oracle VTS Software Packages 67
Detecting Faults Using POST 68
EXAMPLE: PSH Message Output 72
Managing Faults 51 73
Clearing Faults 74
-> show faulty 75
Disabling Faulty Components 77
System Recovery 78
▼ Disable System Components 79
▼ Re-Enable System Components 79
ILOM-to-ALOM CMT Command 80
Reference 80
Managing Faults 59 81
Managing Faults 61 83
Safety Information 85
Safety Symbols 86
Antistatic Wrist Strap 87
Antistatic Mat 87
Required Tools 88
Remotely 88
Powering Off the System 89
Position 91
1 Slide Rail Lock 92
2 Inner Rail Release Button 92
■ Motherboard 93
▼ Remove the Top Cover 95
Servicing Hard Drives 98
# cfgadm -al 100
EXAMPLE: Sample Ap_id Output 101
# cfgadm -c configure c0::sd1 102
▼ Remove a Hard Drive 103
▼ Install a Hard Drive 104
Hard Drive Device Identifiers 105
Servicing Fan Trays 106
About Fan Trays 107
Next Steps 108
▼ Remove a Fan Tray 109
▼ Install a Fan Tray 110
Fan Tray Device Identifiers 110
Servicing Power Supplies 111
About Power Supplies 112
▼ Remove a Power Supply 114
▼ Install a Power Supply 115
Power Supply LED 117
Servicing PCIe Cards 118
▼ Install a PCIe Card 119
▼ Add a PCIe Card 120
PCIe Device Identifiers 121
Related Information 122
Servicing CMP/Memory Modules 124
▼ Remove a CMP/Memory Module 126
▼ Install a CMP/Memory Module 127
▼ Add a CMP/Memory Module 127
Servicing FB-DIMMs 130
▼ Install FB-DIMMs 131
▼ Verify FB-DIMM Replacement 132
▼ Add FB-DIMMs 135
FB-DIMM Configuration 135
Memory Bank Configurations 136
FB-DIMM Device Identifiers 138
Servicing the Front Bezel 141
▼ Remove the Front Bezel 142
▼ Install the Front Bezel 143
Servicing the DVD-ROM Drive 144
▼ Install the DVD-ROM Drive 145
Servicing the IDPROM 149
▼ Install the IDPROM 150
Servicing the Battery 151
▼ Install the Battery 152
Servicing the Motherboard 161
▼ Install the Motherboard 164
Servicing the Front I/O Board 172
▼ Install the Front I/O Board 173
▼ Install the Top Cover 176
1 Inner rail release button 178
2 Slide rail lock 178
▼ Power On the Server 179
CMP/Memory Module 183
# cd /mnt 185
# cp /reconfig.pl 186
# /mnt/reconfig.pl 186
● Do one of the following: 187
System Bus Topology 189
Identifying Connector Pinouts 193
1 Request to Send 5 Ground 194
4 Ground 8 Clear to Send 194
Serial Port Connector Pinouts 196
USB Connector Pinouts 197
Server Components 199
Customer-Replaceable Units 200
Field-Replaceable Units 202
Numerics 205
Index 185 207
Index 187 209
Index 189 211

Kommentare zu diesen Handbüchern

Keine Kommentare

Fujitsu SPARC T5440 Bedienungsanleitung Seite 119

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Server Fujitsu SPARC T5440